Looking for:
Mastercam 2018 lathe live tooling free download |
Mastercam 2018 lathe live tooling free download.Recommended Posts
Case Studies.Mastercam 2018 lathe live tooling free download
Forgot your password? Or sign masteram with one of these services. Register now to participate in the forums, access the download area, buy Mastercam training materials, post processors and more. This message will be removed once you have signed in. By skymontNovember 21, in Industrial Forum. You might want to let us know what kind of problem I'm using and using a surface rough.
My ,ive Plot and Verify shows what Xownload want it to. The lathe mills off some of the part that it is not suppose to touch. I have attached 3 pics to maybe explain more.
The last picture is what the lathe did. Yes your clocking is off. Has nastercam post been tested before now and run other parts with no issue? I look at it more mastercam 2018 lathe live tooling free download then I am not sure. Do you have msatercam file you can share? Mastercam 2018 lathe live tooling free download you called your dealer to see what their take on it is?
No the post has not been tested on milling. Seems to do simple face contour and face drill but this livr now a 1st doing 3D milling. I have mastercam 2018 lathe live tooling free download 2 different roughing tool paths and both do the same surface rough,area rough. I have told the dealer and give them every file mastercam 2018 lathe live tooling free download know program, code and even these pictures. I have not go anything from them.
I think there needs to be a Z axis re-track to clearance move before the lathe does посмотреть еще re-clock. I am thinking it will come down to just dialing in the post. Once that is done you should be good to go. Looks to me like the machine isn't air cutting in the right direction when dree tool stays down. If this is optirough, set to retract to safe height always and see if it перейти на источник up the issue.
If so, basically it is a post issue where you will need to break up angular motion mastercam 2018 lathe live tooling free download force direction. It looks like instead of your "retracts" rotating the "long way mstercam, the machine is taking the "shortest path" on the rotary, and milling off the back side of the part. T to see if it may change. Pay close attention to the moves as you are going through the program.
When you see a C Axis move pay attention its going like you would expect it to and not the opposite direction. I was not thinking about that until Husker and Colin mentioned it and then it lice me I have seen the same thing узнать больше Okuma. There is a нажмите чтобы перейти distance command code for downlozd and if the M15 M16 or M13 M14 depending on the control for CW and CCW direction are not coming out correct mastercan will see the issues you are seeing.
Okay i used the 3 tool offset on the program and it still cut my back side of part. Yes dodnload is throwing out M15 and M16 in to code, but i think it like might need more to keep from cutting back side or it needs to retract in z to allow re-clock.
I have not tried to use a big lead in-out yet i will try this next. His Link:. What happens if you MDI 5 degrees? Does the M15 and M16 influence the direction it rotates to find that position? If the M15 and M16 are working ссылка in the machine, then Colin was right, your machine is going the long way around. Yes we have seen this many times and comes from the NCI out of Mastercam sending bad information. Hard to have a post кажется download python shell for windows 10 неожиданность! fix bad stuff they are getting from the NCI.
Looks like the post logic isn't tracking when it crosses zero correctly. Even though it is outputting C. I just ran this operation through one of our posts and you can see the direction does not change when crossing zero. This post is set up to use the Sign on the Angle instead of a modal M code to indicate the direction, so instead of M16 we have negative C values, and Positive C values for M We didn't provide this post, so I can't change the encrypted logic for you.
Contact your post provider and they should be able to get this downlooad out for you. Look for full vertical retract in the top right dropdown in linking parameters section of ljve path parameters, then in doenload parameters change the value for keep tool down within to a small number, this combo should force retracts.
Does this machine have a milling mode like the Haas? I have found that giving the control the power to use X's and Y's works so much better than using X's and Mastercam 2018 lathe live tooling free download. Plus the code is way smaller. A источник Z retract will not fix this.
Mastefcam interpolation like below should get the part running. Misc Int 9 is set for face interpolation this will convert it to X and Y. It is a Postability Audition download adobe for pc free and I have talked 2108 him and he has not had good results with his reseller.
I will forward to Postability and see if they can assist him through 5th Axis. It is a post problem. I was just making sure I wasn't doing anything wrong in the control definition or my programming before went any further and if anyone had any ideas about fixing this.
You need to be a member in order to leave a comment. Sign up for a new account in our community. It's easy! Already have an account? Sign in here. Together, we are the strongest Mastercam community on the web with over 56, members, and our online store offers a wide selection of training materials for all applications and skill levels. Subscribe to frree News. Industrial Forum Existing user?
Sign /21973.txt anonymously. Or sign in with one of these services Sign in with Facebook.
Sign in with Twitter. Welcome to doownload Register now to participate in the mastercam 2018 lathe live tooling free download, access the download area, buy Mastercam training materials, post processors toolung more.
Use your display name or email address to sign in: Sign In Sign Читать полностью. Sign in to follow this Followers 1. Recommended Posts. Posted November 21, Share this post Link to post Share on other sites. What file do you need and i can try to send it? Colin Gilchrist 3, Posted November 22, Posted November 27, Colin do you know where i can find this retract along z axis? Machine parameter?
Breaking or not rotary motion? Mastercxm High Speed Area Mastercam 2018 lathe live tooling free download. I can post a file if I can. Here is a link to his file: His Link:. Alex Dales What is the Rotary axis type on the machine?
Rocketmachinist Posted November 28, This llve to be a Postability post I wonder why the OP didn't just go back to Dave on this one? I'm thinking this needs an M C axis shortest distance callout We had a lot of trouble with tool paths like this on our Okuma VTM M at appropriate places solved a lot of those issues.
Thanks everyone for the help, maybe by end of week this will be fixed. Create an account or sign in to ltahe You need to be a member in order to leave a comment Mastercwm an account Sign up for a new account in our community. Register a tooking account. Sign in Already have an account? Sign In Now. Recently Browsing 0 members No registered users viewing this page.
No comments:
Post a Comment